The library is read only at present. Is there a way to be able to change this and be able to edit some of the settings ?
Editing layers library.
Best Answer Crow357 , 05 November 2016 - 04:52 PM
Do a save as. Give it a new name. Then load it. Should be good to go.
Go to the full post#1
Posted 05 November 2016 - 01:14 AM
PC specs...
Intel core I7 9700k 3.6 GHZ-Turbo 4.9 GHZ
64 GB Corsair vengeance LPX DDR4 2400 MHZ
Asus PRIME Z390-P
Nvidea GeForce RTX 2060 6GB
X box 360 wired controller
Windows 10 PRO NA 64 bit
#2
Posted 05 November 2016 - 08:30 AM
Tutorials=post #33
Dry Gulch...................Released Smithfield Golf Club...........Released
Millstone Golf Club....Released The Walker Course............Released
Kingsmill Woods Course...Released Pine Lake Golf Club..........Released
Woodhaven Golf Club (9) Released The Reserve at Keowee...Released
Cliffs at Keowee Vineyards..Released The Ace Club...................Released
Dry Gulch 2..........Released Blackberry Oaks.............Released
#3
Posted 05 November 2016 - 04:01 PM
The point I'm making is that my library says "default - read only, hence my question, how to make this editable.
#33 doesn't cover this.
PC specs...
Intel core I7 9700k 3.6 GHZ-Turbo 4.9 GHZ
64 GB Corsair vengeance LPX DDR4 2400 MHZ
Asus PRIME Z390-P
Nvidea GeForce RTX 2060 6GB
X box 360 wired controller
Windows 10 PRO NA 64 bit
#4
Posted 05 November 2016 - 04:52 PM Best Answer
Do a save as. Give it a new name. Then load it. Should be good to go.
Swing Type: Tour Pro Wireless XBox 360 Controller.
#5
Posted 05 November 2016 - 04:54 PM
I think he refers to .... go to Menu (in Unity) Perfect Parallel --> Course Forge Settings --> Advanced Mode ... to enable the possibility to edit the Layer Settings .... should be really covered in the video (if you take time to watch it full) if it's not the wrong video he pointed out. Sry, no time to check this.
- RobC likes this
#6
Posted 06 November 2016 - 01:06 AM
I've already set course forge settings to advanced. All that does is enable the library to be opened and inspected. It still says read only !
Crow, I will try your suggestion thanks.
PC specs...
Intel core I7 9700k 3.6 GHZ-Turbo 4.9 GHZ
64 GB Corsair vengeance LPX DDR4 2400 MHZ
Asus PRIME Z390-P
Nvidea GeForce RTX 2060 6GB
X box 360 wired controller
Windows 10 PRO NA 64 bit
#7
Posted 06 November 2016 - 04:48 AM
Captain, did you happen to start a completely new project? I have run into the same situation while attempting a project from scratch. When I loaded up the original terrain and scene all was back to normal and layers were customizable again, yet when I go back to my new project (also saved with a different name and reloaded) the layers were once again read only. Sorry I don't have a solution just a few clues to hopefully find it.
#8
Posted 06 November 2016 - 08:08 AM
To be a little more specific on Crow's answer you need to change the name of the layer lib, save, and reload not your project.
#9
Posted 06 November 2016 - 01:42 PM
Do a save as. Give it a new name. Then load it. Should be good to go.
Thanks Crow. The lib is now editable.
PC specs...
Intel core I7 9700k 3.6 GHZ-Turbo 4.9 GHZ
64 GB Corsair vengeance LPX DDR4 2400 MHZ
Asus PRIME Z390-P
Nvidea GeForce RTX 2060 6GB
X box 360 wired controller
Windows 10 PRO NA 64 bit
#10
Posted 06 November 2016 - 01:43 PM
Captain, did you happen to start a completely new project? I have run into the same situation while attempting a project from scratch. When I loaded up the original terrain and scene all was back to normal and layers were customizable again, yet when I go back to my new project (also saved with a different name and reloaded) the layers were once again read only. Sorry I don't have a solution just a few clues to hopefully find it.
No this didn't happen.
PC specs...
Intel core I7 9700k 3.6 GHZ-Turbo 4.9 GHZ
64 GB Corsair vengeance LPX DDR4 2400 MHZ
Asus PRIME Z390-P
Nvidea GeForce RTX 2060 6GB
X box 360 wired controller
Windows 10 PRO NA 64 bit
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users